|
SANY5519
Here we have our oem Civic
Date: 09/12/2007
Views: 125
|
SANY5520
Here it is after removing the front bumpers fenders and headlights.
Date: 09/12/2007
Views: 117
|
SANY5521
There are two tabs on the front of the radiator support that we need to remove.
Date: 09/12/2007
Views: 101
|
SANY5522
Date: 09/12/2007
Views: 90
|
SANY5523
They are only secured by 2 spot welds, if you take a firm grip of the bracket and bend it left and right it will come right off after several bends.
Date: 09/12/2007
Views: 93
|
|
SANY5524
After removing them make sure to hit them with some paint or something so it doesnt rust.
Date: 09/12/2007
Views: 90
|
SANY5525
Headlights attached.
Date: 09/12/2007
Views: 139
|
SANY5526
Carbon fiber hood and fenders attached. As you can see the front point of the fenders are still a bit out of wack.
Date: 09/12/2007
Views: 128
|
SANY5527
Heres the stock 99-00 headlight sprayer. they have this little extrusion that needs to be shaved down.
Date: 09/12/2007
Views: 96
|
SANY5528
Like so.
Date: 09/12/2007
Views: 94
|
|
SANY5529
Still need to fix these points. I will have to make a couple cuts and bend it into the correct shape.
Date: 09/12/2007
Views: 102
|
SANY5530
Drivers side is only a bit better than the passenger side.
Date: 09/12/2007
Views: 93
|
SANY5531
after 3 days of welding, shaping, sanding bondo and using a body file, the fenders are finally in place and primered.
Date: 09/19/2007
Views: 114
|
SANY5532
Date: 09/19/2007
Views: 102
|
SANY5533
Date: 09/19/2007
Views: 98
|
|
SANY5534
The Domani bumper will take some modifying to fit on my car.
Date: 09/20/2007
Views: 101
|
SANY5535
Due to the intercooler I need to trim some of the plastic.
Date: 09/20/2007
Views: 93
|
SANY5536
I cut between this and the previous picture to make a notch for the intercooler
Date: 09/20/2007
Views: 93
|
SANY5539
Here is where the bumper support has to be cut.
Date: 09/25/2007
Views: 101
|
SANY5540
Date: 09/25/2007
Views: 91
|
|
SANY5541
and last but not least wiring. the domani has a parking light on the headlight but the blinker is down on the bumper like on accords and integras. Extend the green wire and the ground to the blinker on the bumper and tap into the red and the black for the
Date: 09/25/2007
Views: 107
|
SANY5537
The front bumper support needs both ends trimmed 1 inch from the bottom and about 2.5 inches from the end.
Date: 09/20/2007
Views: 156
|
SANY5538
Date: 09/20/2007
Views: 208
|
SANY5806
Brackets fabbed and welded.
Date: 06/18/2008
Views: 119
|
SANY5808
Painted with paint from Paintscratch.com 1+ can of color and 1 full can of clear for the bumper.
Date: 06/18/2008
Views: 111
|
