http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/ en-us Gallery 2 RSS Module, version 1.1.8 Wed, 10 Mar 2010 07:08:20 -0700 120 http://repo.jackmoves.com/d/10553-4/album158.jpg http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/ http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0450.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0450.jpg.html
Here it is installed. Its not as nice as say a laser cut valve cover but its a crap load cheaper.]]> Erik M. photo Tue, 17 Jan 2006 22:01:16 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0449.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0449.jpg.html
Do the same on the upper timing belt cover and youre good to go.]]> Erik M. photo Tue, 17 Jan 2006 22:01:15 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0448.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0448.jpg.html
Here is the finished valve cover.]]> Erik M. photo Tue, 17 Jan 2006 22:01:15 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0446.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0446.jpg.html
With the dremmel and a few cutoff wheels start to cut your vfalve cover.]]> Erik M. photo Tue, 17 Jan 2006 22:01:15 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0445.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0445.jpg.html
the center of the gear lines right up with the bottom of the valve cover. scratch arround the template to make your mark.]]> Erik M. photo Tue, 17 Jan 2006 22:01:15 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0444.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0444.jpg.html
After you install the timing belt and check the timing marks, lay out the stock cam gears on a template and draw arround them.]]> Erik M. photo Tue, 17 Jan 2006 22:01:15 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0438.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0438.jpg.html
Carefully slde off the old cam gears and take care not to drop the keys into the lower timing belt cover or you will have to remove the crank pulley and lower timing belt cover to retrieve them (not pictured... yes i dropped one). Place the new cam gears on and hand tighten the bolts.]]> Erik M. photo Tue, 17 Jan 2006 22:01:14 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0436.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0436.jpg.html
Loosen the tensioner 1/2 turn and slide the timing belt off the cam gears.]]> Erik M. photo Tue, 17 Jan 2006 22:01:13 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0435.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0435.jpg.html
Set cams/crank pulley to top dead center (TDC). Break the cam bolts free at this point.]]> Erik M. photo Tue, 17 Jan 2006 22:01:13 -0700 http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0434.jpg.html http://repo.jackmoves.com/v/erik/album53/album96/album129/album157/album158/SANY0434.jpg.html
You will need to remove this cap before you can see it.]]> Erik M. photo Tue, 17 Jan 2006 22:01:13 -0700